In this episode
- The final three courses laid freehand to bring the well to full height
- Joints cleaned with brushes, trowels, pointing irons and a tree branch
- Climbing inside the well to finish the interior
- Two old metal lids cut, sanded, straightened and treated for rust
- A barbecue cheeseburger on the veranda to end the week
The well reaches full height
This week I finish the water well and restore its old metal lids. In episode 46 I laid the first three courses of handmade terracotta bricks around the opening. Now I push through the heat to lay the final three, freehand with no spirit level, mixing mortar in the wheelbarrow and working the bricks round the circle from the stack on the pallet. Without the level, each brick is judged by eye against the course below, with the practice of the first three courses behind me.
With six courses down, the well is at its finished height, which turns out to be just right to work as a table, or even a seat. Once the terrace around it is backfilled, only the top courses will stand above the patio.
Cleaning the joints inside and out
Next I clean up the outside of the well, scraping and smoothing the excess mortar from the joints with a pointing trowel, brushes, pointing irons and even a tree branch. The bottom three courses will be buried under the terrace, so there is no point spending time tidying those.
I was not sure whether to point the brickwork fully, so for now I leave the joints as they are. Once it is done, there is no undoing it, and I ask what you think: fill the joints, or keep them as they are? My article on traditional mortar and Sicilian stonework covers why decisions like this are worth pausing over.
Inside the well, facing my fears
The inside needs cleaning too, and the only way to reach it properly is to climb in. In a straw hat, with scrapers, wire brushes and a hand broom, I work round the interior walls of all six courses, scraping and brushing every joint clean. Facing my fears is the right way to describe it, but the interior is the part that stays on show, so it has to be done.
Then a site clean up. The leftover bricks are stacked and stored, and the tools, plastic wrapping and empty pallets are cleared from the terrace.
Restoring the old metal well lids
In the garden I found two old semicircular steel lids, rusty and battered. I bring them over from the terrace wall and test them on top of the new brickwork before taking them to the veranda to restore them. Reusing what the house already has is a theme of this project, from the bed frames in the well base in episode 39 to the doors I am keeping in episode 45.
The restoration takes the rest of the week:
- Cut off the old protruding brackets with the angle grinder and grind the welds flush.
- Fit fresh paper to the orbital sander and sand the rust and scale off both lids.
- Heat the bent handle in the fire pit and straighten it, and the bent edges, with a hammer.
- Vacuum off the dust and spray both sides with rust converter to stop further rusting.
- Brush on a coat of white metal primer for extra protection from the elements.
I have not chosen a colour for the lids yet, so I ask which you would paint them. Cleaning out the well shaft itself, and making a proper cover, follows in episode 49.
What finishing the well unlocks
Finishing the well is one of two jobs holding up the terrace. As I explained in episode 44, only once both the well and the underground rainwater tank are complete can I backfill the terrace and properly build the outbuilding. That building will hold two 450 litre pressure tanks, the filtration and a gas boiler, with water pumped from the well and the tank, filtered, then sent to the boiler or straight into the cold line to the house. With the well done, the rainwater tank is the last big piece, and I start marking it out in episode 75.
A barbecue cheeseburger
To finish, burgers on the barbecue. I slice onion and tomato, grill the patties over the coals, melt cheese on top and build a cheeseburger with lots of salad and burger sauce, then sit on the log bench on the veranda with a cold drink. Cheers, everyone. Are you team classic, or do you go all out on the toppings?
The well is a big part of the off grid water plan, and my article on off grid versus mains water explains how it will work alongside the underground rainwater tank.
Frequently asked questions
How do you restore rusty metal lids?
I ground off the old brackets, sanded off the rust, heated and hammered the bent handle straight, sprayed on rust converter, then brushed on a white metal primer.
Should you point the joints on a brick well?
I cleaned mine but held off filling them, because once pointed there is no undoing it. I asked viewers whether to fill the joints or keep the look as it was.
How do you clean mortar off curved brickwork?
I used a pointing trowel, brushes and pointing irons on my well, and even a tree branch. The bottom courses that would be buried I left alone.
What height should a garden well be?
At six courses of terracotta brick, my well came out at a height that works as a table or even a seat once the terrace around it is filled.
More episodes on the same job: Water and plumbing



