In this episode

  • A 110mm core drill bit brought over from the UK
  • The extractor fan wired to come on with the kitchen lights
  • A bouncing section of hallway floor concreted solid
  • A new drain pipe slid inside the old, blocked kitchen drain
  • Rusted metal door frames rebuilt with polyester metal filler

Core drilling for the extractor fan

This week I core drill through the stone wall for the kitchen extractor fan, then tackle the old kitchen drain at last. I have not seen core drill bits like this in Sicily, so I brought one over from the UK. I fit the 110mm bit, its extension bar and pilot drill onto the SDS drill, climb the stepladder and drill through the wall near the ceiling, then knock out the cut plug of masonry and finish through the outer layer.

It is easy going compared with home. The soft Sicilian stone cuts much more readily than the tough Yorkshire stone I am used to back in the UK. The run for this ducting was chased out in episode 45.

Wiring the fan to the lights

Next, I fit the extractor fan ducting and run black flexible electrical conduit through the chases in the ceiling and upper wall. The cables for the extractor fan meet the cables for the light, so when the lights are switched on, the extractor comes on automatically. Then I fill the chases over the conduit with mortar using a trowel and spatula.

In the hallway there is a section where loose tiles have been bouncing underfoot. I wet the trench with the pump sprayer, shovel in concrete from the wheelbarrow, level it with a timber straight edge and trowel it flush with the tiles around it. A solid base matters because the new floor tiles will go straight over the old ones, as I explain in episode 64.

A stray puppy on the way to the Brico

This morning, driving to the Brico, I found a little soul on the roadside, a young tan puppy scavenging among dumped bathtubs and rubbish. Alone, hungry and still very young. I wanted to help, but I am still living between the UK and Sicily and not yet living at the villa full time, which limits what I can take on. I come back to the puppy at the end of the week.

Replacing the old kitchen drain

Then the big plumbing job. In episode 45 I unblocked the kitchen drain, but there is still a lot of debris stuck in the pipe. I break out the concrete around the old pipe junctions with the breaker, cut through the waste pipes with the angle grinder and push a drain rod down the line to find the obstruction. When I find it, it feels like the pipe is filled with cement. In hindsight, I should have tackled the drainage before the electrical ducting.

Here is the culprit: years of dirt build up. It looks like the rats threw a party in the old pipes, and even some snails turned up. I clear out decades of debris, cut the old pipe square and slide a new drain pipe inside the old one.

Solvent weld fittings and sweeping bends

Plumbing supplies here work a little differently from the UK. The builders' merchants supply waste pipe with flared, belled ends rather than separate couplers, so every length has to be cut and dry fitted carefully. Solvent weld cannot be taken apart once it sets, so I trim each piece, wipe the ends and test the elbows and sweeping bends before gluing anything. Sweeping bends give the waste a gentler path round corners than tight elbows.

With the run in place, I damp the trench down with the sprayer, shovel concrete around the new pipe and trowel it smooth, then do the same along the long hallway trench, levelling it with an aluminium straight edge. The new soil pipe out to the cesspit follows in episode 53, and my guide to setting up utilities in rural Sicily covers drainage alongside water and power.

Restoring the metal door frames

After asking whether to keep or replace the doors and frames in episode 43, most of your comments said keep them, so I am. The bottoms of some metal frames are rusted away, so I vacuum out the rust and dust, mix a two part polyester filler designed for repairing and rebuilding metal, and press it into the voids. Once cured, it is sanded flush with the palm sander and the frames get a coat of white primer.

I have not decided on a final colour yet. I am really pleased with how they have turned out, and once the plastering is done I will sand and repaint them so they are perfect. The doors themselves are restored in episode 51.

As for the puppy, I tried to coax it, but it ran off into the open fields. I have had to draw a line at taking on sick or injured animals until the villa is finished, and I hope to do more for animal welfare once I am settled here for good.

Frequently asked questions

What size core drill do you need for an extractor fan?

I used a 110mm core drill bit on an SDS drill to go through the kitchen wall. I could not find bits like it in Sicily, so I brought one from the UK.

How do you make an extractor fan come on with the lights?

In my kitchen the cables for the fan were run to meet the lighting cables, so switching the lights on starts the extractor automatically.

How do you repair rusted metal door frames?

I vacuumed out the loose rust, filled the holes with a two part polyester filler made for rebuilding metal, sanded it flush and primed the frames.

How are Italian waste pipes joined?

The pipes I bought here come with flared, belled ends instead of separate couplers, so I cut and dry fitted every piece before solvent welding, because it cannot be undone.

More episodes on the same job: Air con and ventilation