In this episode
- Marble windowsills from a local Sicilian supplier
- Plasterers wanted €500 to €1,000 extra for the reveals, so I do them myself
- Reveals rendered against timber profiles for clean, straight edges
- A manual pressure test on the hot and cold pipes, with no leaks
- The first sill bedded level, with a slight fall to the outside
The marble windowsills arrive
This week I install the first marble windowsills and pressure test the plumbing. Most of this renovation has been dusty, messy work. This week, for the first time, we can see where it is heading. After sourcing marble from a local Sicilian supplier, I protect the lounge and carry the new sills in from the car, stacking them upright against the wall.
Why I am rendering the reveals myself
When I first got quotes from plasterers, I assumed the window reveals would be included. It turns out they wanted €500 to €1,000 extra to do them, so I decided to tackle them myself. It has been a lot of extra work and a steep learning curve, but with each one I get better. Another skill I did not have before. I started on them in episode 62, and the sills and openings were rebuilt in episode 60.
Renovating in an unfamiliar climate has its challenges, and choosing appropriate clothing is one of them. Like and subscribe for more Italian fashion inspiration. My real world renovation cost breakdown shows how savings like this add up.
Rendering the bedroom window reveals
The kids' bedroom window is first. Each reveal goes in stages:
- Measure the opening with the spirit level and a straight edge.
- Fix temporary timber profiles around the opening, braced across it, to set the line and depth.
- Brush on bonding primer.
- Apply the mortar from the hawk with a plastering trowel and shape the edge.
- Take the timber away to leave a clean, straight edge.
The tall reveals need the ladder, standing on the window ledge with battens clamped across the opening, working into the evening by head torch.
The bathroom window and the double doors
In the bathroom, the window I reshaped in episode 60 gets the same treatment: measured, boarded, rendered and the boards removed. Then I repeat the process on the doorway reveals, smoothing the mortar along the jambs with a float. Under the bathroom window, I cut back the concrete and stone with the SDS and chisel bit to make room for a proper mortar bed and fall under the sill.
The double door reveals follow, rendered along the bottom and sides with the hawk and trowel, using the ladder and a chair to reach the top sections.
Pressure testing the water pipes
A few of you asked in the comments how I know the pipes will not leak, so I wanted to show this. I test the hot and cold water system with a manual pressure pump. I fill the pipes with water and pump them up to a pressure higher than normal working pressure, then watch the gauge.
If the needle drops, there is a leak. If it stays solid, the system is sealed. If it can hold pressure under test conditions, it is not going to leak under normal use. The needle stays put. No leaks. These are the crimped PEX pipes from episode 62, and the shower valves get the same test in episode 79.
Building the kitchen window reveal
Outside, I climb the ladder, take the OSB board off the kitchen window and clamp timber formwork around the opening, then render the external reveals and the top of the opening. The kitchen window was the one I took out in episode 59. All these clean, straight edges are ready for the new aluminium windows, which are fitted in episode 88.
The first marble windowsill
To set the sills, I first work out the levels. With a cut timber block, a tape measure and a hand drawn diagram of the reveal depth and the internal and external offsets, I mark the cut lines on the concrete sub-sill. I cut the stone with my Makita and drill a line of holes along the mark with a long bit on the SDS, then chisel the shelf down to the right level.
I left myself plenty of room here, so I could lay a solid bed of mortar to get the sills perfectly level, with the correct fall. After sweeping up, I trowel a thick bed of mortar onto the ledge, lift the dark veined marble sill into place, tap it down and check it with the spirit level: perfectly level along its length, with a slight fall to the outside so rain runs away from the window. One of the cats hops straight up and walks across it.
Finishing the sill edges
The bathroom sill follows. I tape its edges, lay the mortar bed and press it firmly into place. Once it has set, I cut the tape with a knife and peel the protective film off the polished stone, then brush it clean. It is another visible step towards a year-round Sicilian home. More sills, and the kitchen floor, follow in episode 64. My guide to buying, renovating and living off grid in Sicily and my practical renovation guide show how it all fits together.
Frequently asked questions
Do plasterers in Sicily include window reveals?
Not in the quotes I got. The plasterers wanted €500 to €1,000 extra to do the window reveals, so I decided to render them myself.
How do you pressure test new water pipes?
I filled the pipes with water, pumped them above normal working pressure with a manual pump and watched the gauge. If the needle stays solid, the system is sealed.
How do you set a marble windowsill?
I cut the sub-sill down to leave room for a solid mortar bed, then set the marble on it, level along its length with a slight fall to the outside.
Why should a windowsill have a fall?
I set my marble sills with a slight external fall so that rain runs away from the window rather than sitting on the sill.
More episodes on the same job: Water and plumbing · Windows and doors



