In this episode

  • A pine slab from the timber merchant, sanded with its rough edge kept
  • A clear matt outdoor oil that resists UV, weather and greying
  • The curved tower doorway squared off to let in more light
  • The sill cut to size with a chainsaw
  • Set in mortar with the correct fall for water runoff

Sanding the pine slab

This week I make a pine door sill for the tower. I recently bought a thick pine slab from the timber merchant, and once it is sanded and sealed it will be the sill for the tower doorway onto the roof terrace. I bring it into the house and set up a temporary bench on timber blocks.

The top, the bottom and the edges are sanded with the belt sander, then the detail sander and a sanding block. I love the rough edge, so I clean it up and leave it just as it is. After brushing and vacuuming off the dust, I coat it with a clear matt outdoor wood oil. It is UV and weather resistant and helps stop the wood greying.

A mantis and the cats

Under the torch, there is a praying mantis on the wall of the room. Then it is feeding time, with dry food in the pink bowl on the log bench under the veranda for two of the cats.

Broken pots and pine stumps

Overnight, two of my terracotta pots were smashed, either by the wind or by the cats on the hunt. I clear the broken pieces and soil off the front steps, and water the lavender I planted in episode 64.

On the veranda there are some pine tree stumps. I really wanted to keep the bark on them, but over time it dried out and completely separated from the wood. So I strip it off, stack the bark in the firewood shelter and brush the stumps clean. They will become rustic seats, and we have a few more ideas for using them in the house, like bedside tables. A gecko climbs the wall while I work.

Almond branches and prickly pear

In the garden, I cut back the almond tree branches, break them down and carry the piles across the lawn. Then the pruned prickly pear pads are chopped and loaded up for the compost bag I set up in episode 65, with one of my boys helping. My article on growing your own food in Sicily covers the garden and orchard.

Squaring off the tower doorway

Up on the roof terrace, it is time to sort out the tower doorway. The opening is much smaller inside than outside because of the curve of the tower, so I am going to square it off. That maximises the light and makes installing a door much easier, giving the right space for a future external door. I opened the tower up to the roof back in episode 42.

  1. Take down the temporary OSB security door and its frame.
  2. Cut vertical guide lines along the inside and outside edges of the opening with the petrol concrete saw.
  3. Chisel away the concrete, render and masonry on the sides with the SDS to square the opening off.
  4. Drill a row of holes along the base with a long masonry bit and break out the old concrete sill.
  5. Sweep the rubble into buckets and carry it down the stairs.

I used the same saw and SDS to round off the corners into the tower in episode 50. My article on traditional mortar and stonework covers the walls themselves.

Cutting the sill with a chainsaw

Back at the workbench, I measure the opening onto the slab with a tape, speed square and straight edge, and mark the cut lines in pencil. It is cut to size with the chainsaw, with one of my boys holding the other end. The cut end grain is then sanded smooth with the palm sander, and I take a tea break on the veranda bench with one of the cats.

The sill goes up through the tower to the roof for a test fit. It sits in the opening and I check it with the spirit level, then take it out again and sweep the dust and stone chips off the threshold.

Setting the sill in mortar

Downstairs, the leaf blower clears the concrete dust out of the living space while the mixer turns, and the front garden gets strimmed. Then, by head torch, I spread a bed of mortar across the threshold with the trowel and hawk, set the pine sill into it with the correct fall for water runoff, and check it with the level.

From the ladder inside the tower, I pack and smooth mortar underneath and around the sill, then carry the leftover mortar back down in buckets. The tower now has a solid timber threshold ready for its new door. My practical guide to renovating in Sicily and my article on rural life in Sicily show how jobs like this fit into a week here.

Frequently asked questions

Can you use pine for an external door sill?

I used a thick pine slab for my tower door onto the roof terrace, sanded it and sealed it with a clear matt outdoor oil that is UV and weather resistant.

Why square off a curved doorway?

My tower doorway was much smaller inside than outside because of the curve, so I squared it off to let in more light and make fitting a door easier.

How do you cut a thick timber slab to size?

I marked the cut lines with a tape, speed square and straight edge, then cut the pine slab with a chainsaw while someone held the other end.

How do you set a timber door sill?

I spread a bed of mortar across the threshold, set the pine sill into it with the correct fall for water to run off, checked it was level and packed mortar underneath.

More episodes on the same job: Windows and doors