In this episode

  • The old hallway electric box prised off the wall
  • Ducting finished up the tower for the lights and switches
  • A socket and ducting chased into the roof terrace wall
  • Square corners into the tower cut round with a concrete saw
  • Five patio lights marked and chased into the back wall

Core drilling for the bathroom fan

This week I core drill for the bathroom extractor fan, after doing the same for the kitchen in episode 48. First, the old grey electric box in the hallway is prised off the wall with a crowbar. Then, up the ladder in the bathroom, I drill through the wall near the ceiling with the SDS for the fan and chase the channel for its cable, before sweeping up.

Ducting up the tower and on the roof

In the tower, I run the black flexible conduit up the groove I chased in episode 45, working from the ladder and the roof landing, and fix it in with expanding foam. Then up on the roof terrace, I chase out channels along the low perimeter wall and the base of the tower with the grinder and SDS, fit a socket back box on the roof terrace and drill through the tower wall to pass the conduit into the chase. Finally the runs are foamed and mortared in. The roof is about 100 square metres, as I mentioned in episode 42, and I still have not decided exactly what it will become, but whatever it is, it will need power, so the socket goes in now while the walls are still open.

I will be glad to see the back of all this chasing and ducting. Just when I think I am close to finishing, the electrician points out more to be done. But it is absolutely essential to cover every base with the electrics, planning for future needs and making sure the lights and sockets are in the right places. Once the floors are tiled and the walls plastered, adding cables becomes almost impossible.

Why I bought my drills in the UK

I have brought a DeWalt combi drill and impact driver over from the UK. Here in Sicily, DeWalt tools are almost twice the price, so it made sense to buy them there. It is one of the small ways prices differ between the two countries, which my UK versus Sicily cost of living guide covers in more depth.

While fixing the tower ceiling ducting, and treating the exposed rebar there with rust converter, I manage to get expanding foam all over my arm. If anyone can recommend a better way to get it off arm hair, please let me know. I am just grateful it did not end up on my head. Then the ladders come down and everything is locked up.

Rounding off the corners into the tower

In episode 42 I asked whether the corners of the opening between the lounge and the tower should stay square or be rounded. Your comments came down firmly on the side of rounded, with messages like rounded is best and votes for rounded edges, so rounded it is.

With the laser level on a chair to mark the lines, I cut back the square stone edges with my Stihl concrete saw, then shape the curve with the SDS and a chisel bit, filling the room with dust. The rubble is shovelled into the wheelbarrow and the threshold swept clean. The softer shape suits the curve of the tower, under the oak lintels from episode 36.

Five lights for the patio

Outside, the rear terrace gets a clean up, with the stone debris cleared and the ground raked. Then I mark out the garden lighting on the back wall of the house. There will be five lights along it. I plan to make the most of the patio, so it needs to be well lit, and a black cross marks where each light will go, measured out with a level and tape.

From the extension ladder I drill and chase a vertical groove at each of the five marks, wheel the rubble away, then wet the chases with the pump sprayer and mortar in the conduit and back boxes. The trenches and junction boxes that take this power out into the garden follow in episode 55.

Mortaring with my little helper

Up on the roof terrace, one of my boys helps sponge and smooth the mortar over the conduit. Finished? Yes. Looks good, and he gives a thumbs up against the evening sky. I carry on by head torch, smoothing mortar over the conduit runs all the way up the curved tower wall, before packing up as a cat wanders through. My utilities guide explains how the electrics fit with the rest of the services.

Frequently asked questions

Why plan electrics before tiling and plastering?

Once the floors are tiled and the walls are plastered, adding cables becomes almost impossible, so I made sure every light and socket was planned and ducted first.

Are power tools cheaper in the UK than in Italy?

In my experience DeWalt tools cost almost twice as much in Sicily, so I bought my combi drill and impact driver in the UK and brought them over.

How do you round off a square stone corner?

I cut back the square edges with a petrol concrete saw, then shaped the curve with an SDS drill and chisel bit, which gives a lot of dust.

How many outdoor lights does a patio need?

I planned five along the back wall of my villa, because I want to make the most of the patio and it needs to be well lit.

More episodes on the same job: Air con and ventilation