In this episode

  • Perimeter cuts scored and snapped on a manual tile cutter
  • L-shaped cuts around the entrance doorway reveal
  • A tile scribed and cut to the curve of the tower wall
  • Door frames undercut so the tiles slide underneath
  • Starlink internet live at the villa for the first time

Starting with the easier cuts

This week I show how to scribe floor tiles around a curved wall, along with all the other awkward cuts. Last week, in episode 86, I laid my first ever floor tiles. Somehow, I have made it this far without ruining the tiles, the floor or my budget. This week I am tackling the awkward corners, doorways and tricky cuts. So this is where we find out: have I learned another new skill, or is this a step too far?

I start with some of the easier cuts along the perimeter walls. I measure each edge gap with a tape, mark the porcelain tile in pencil, then score and snap it on the manual tile cutter I set up last week. It is cutting through the porcelain like butter.

  1. Spread the adhesive along the wall edge with a notched trowel.
  2. Back butter the cut piece.
  3. Seat it firmly and tap it level with a rubber mallet.
  4. Fit the levelling clips and wedges.
  5. Wipe the tile faces clean with a damp sponge.

For anyone who does not know, the clips and wedges keep the tiles level with each other while the adhesive sets, so you do not end up with one edge sitting higher than the next.

L-shaped cuts around the entrance doorway

The rescued kitten from episode 85 gets fed, and is settling in brilliantly. Then it is the entrance doorway. The tiles here have to wrap around the doorway reveal, so they need L-shaped cuts. I trace the exact notches onto each tile with a metal multi-angle template ruler and a pencil. Out on the portico, with the tile resting on a bucket, I cut the profile with the angle grinder and a diamond disc and snap off the waste corners. Then the notched tiles go down in the doorway on a bed of adhesive, with clips, and a sponge to clean the joints.

Scribing a tile around the curved tower wall

The trickiest cut is where the floor meets the curved wall of the tower. There is no straight line to measure to, so the curve has to be scribed onto the tile:

  1. Align a full tile in position, using timber spacer battens.
  2. Scribe the curve of the wall base onto the tile with a pencil.
  3. Check the measurements with the tape.
  4. Outside, cut the smooth arc along the pencil line with the angle grinder.
  5. Dry fit the tile, and chip away excess mortar and plaster at the base of the wall with a hammer and cold chisel for a flush fit.
  6. Spread and comb the adhesive, then lay the curved tile and the tiles around it and lock them with wedges.

I am deliberately leaving a small expansion gap around the edges, which will be hidden by the tiled upstand or skirting. The tower room was opened up in episode 42, and its pine door sill was made in episode 66.

Undercutting the door frames

Next, I undercut the metal door frames so the tiles slide neatly underneath. I mark the height on the frame, cut it with the angle grinder and clear it out with a hammer and chisel. The kitchen floor tiling starts too, and once the earlier sections have set, I remove the clips and spacers from the lounge floor.

Cutting down a door for the new floor

The new floor is higher than the old one, so the internal doors come off their hinges. Out on the portico, with a door across two sawhorses, I clamp an aluminium straight edge as a guide and trim the bottom with a circular saw, sand the edge smooth and rehang it to test the clearance. The kitchen door is trimmed the same way.

The window fitters were due to start the next day, so rather than carry on tiling and risk them stepping on wet tiles, I stop and have a good clean-up ready for them, sweeping and vacuuming the joints. Unfortunately, their transport broke down, which causes a bit of a delay. Hopefully they will be here in the next few days, so the windows can finally go in and I can get back to finishing the tiles.

Cleaning the robbed beehive

This is the hive that was ransacked after robbing, in episode 85. I vacuum out the box and frames, give it a thorough clean, reassemble it and put it to one side for now. I have probably missed the window for catching a new colony this year, but if the other colonies keep thriving, it will not be long before I can split one of them. My article on my first year of beekeeping covers splits and swarms.

Then a big milestone. I unbox the Starlink dish, set it on the flat roof and pull its cable down into the kitchen through a conduit that was already in place. I put that ducting in when the old metal water pipe was removed. I did not know exactly what I would use it for at the time, but I do not think you can future-proof a project like this too much, and I knew it would come in handy eventually. For now it carries the cable from the dish to a socket in the kitchen. Eventually, I will move the dish to the top of the tower, out of the way. I connect the router, and the phone confirms it: the villa has internet. My article on living off grid in Sicily covers how this fits the bigger plan.

Security cameras, front and back

With the Wi-Fi working, the next job I have wanted to do for a long time is put up some security cameras, for peace of mind while I am back in the UK. I know I mention security quite a lot, and it may sound as though I am being overly cautious or that the area is particularly high risk. That is not the case. I pair a hub and two cameras, then mount them on the outside of the house, front and back, so I can check on the cats and the fruit trees from the UK.

  • They send an alert if they detect someone, and record clearly by day or night.
  • They can tell people apart from vehicles and animals, which cuts down on unnecessary notifications.
  • They pan, tilt and zoom, so I can turn them remotely.

This is only a temporary setup. The house still needs rendering, and I will have permanent electrical outlets installed before mounting the cameras in their final positions. To finish, I adjust one of the bird boxes on the tower wall, where the sparrows are feeding their chicks, the same boxes where I found four chicks in episode 81. My article on what I wish I had known before buying covers more of the practical side.

Frequently asked questions

How do you cut a floor tile to fit a curved wall?

I aligned a full tile with timber spacers, scribed the curve of the wall onto it in pencil, then cut the arc with an angle grinder and dry fitted it.

What do tile levelling clips and wedges do?

They keep the tiles level with each other while the adhesive sets, so you do not end up with one tile edge sitting higher than the next.

Should you undercut door frames when tiling?

I undercut the door frames in my villa with an angle grinder and chisel, so the new floor tiles slide neatly underneath them.

Why leave an expansion gap around floor tiles?

I deliberately left a small expansion gap around the edges of my floor, which will be hidden by the tiled upstand or skirting.

More episodes on the same job: Tiling the floors