In this episode
- A new €90 SDS drill after the last one snapped in half
- A one foot thick stone wall knocked through between the lounge and tower
- A €6 chain sharpening that turns the chainsaw back into a beam cutter
- The first oak beam lifted into its pocket single handed
- A 100kg second beam that has to come down and go up again
Make or break, and full of cold
This week I install two heavy oak beams as lintels over the doorway into the tower, completely on my own. This week could make or break the build. The beams are heavy, awkward and unforgiving, and one wrong move could be game over. I sanded them back in episode 34 and they look incredible, but getting them safely into place is going to take everything I have. To make it harder, I am full of cold, with a constantly running nose. Lewis has gone home, so the lifting I was dreading back in episode 33 is now mine alone.
A new SDS drill
My last SDS drill literally snapped in half while I was knocking through this wall in episode 33. I took it back to Leroy Merlin, but their policy is to send it away for repair, and I cannot sit around waiting with this much knocking through left to do. So I bought another one.
It is a Dexter, a DIY brand, and it cost €90 with what I think is a three year warranty. Professional brands like DeWalt or Makita are around €400. I have used the last one extensively, so with that warranty, buying another of these makes sense and gives me some peace of mind. If you are budgeting tools for your own project, my renovation cost breakdown covers what things really cost here.
Knocking through a one foot thick wall
The wall between the lounge and the tower is about a foot thick. Standing on the work table and a ladder, I knock out the masonry above and around the doorway with the new drill and a chisel bit, clearing the rubble into the wheelbarrow as I go, in safety glasses, a respirator and ear defenders. An acrow prop has bent, so I straighten it before trusting it, then set it against the ceiling and test it by hand. Wishing I had an extra pair of hands right about now.
Then the old concrete lintel comes out, alone. With the opening clear, I mark out and chisel the pockets in the masonry where the ends of the oak beams will sit, checking the level across the opening with a laser line and measuring the depth and width with a tape.
Cutting reclaimed oak to size and angle
Because the tower wall is curved, the beams sit back to back and need angled ends. I make a simple guide from scrap timber, screw it to the first beam and use it to steer the chainsaw. I found a local shop that sharpens tools, and €6 to get the chain sorted means it now cuts through this oak like butter.
With the first beam cut, I lift it onto the work table, rest one end on the ladder and the wall ledge, then push and lever it overhead into its pocket until it is fully seated. The first beam goes in without too much trouble, or so it seems.
The nightmare 100kg beam
The second beam goes into the curved tower side of the wall. From a ladder inside the tower, I chip out more masonry to make room for it, then mark and cut its angled end by head torch. At around 100kg, it is the heavier job, and the tight curved opening fights me all the way. I end up stuck between two ladders, wedging, adjusting and pushing, and by 10:40pm I am tired, hungry, aching and fed up, but determined to finish.
It still will not sit right. So I lower it back onto the table, trim a sliver off the end with the chainsaw and lift it all over again. This time it slides into place flush beside the first, and a spirit level under the two beams confirms they are true.
A 12:10am finish
Then the clean up: offcuts, sawdust and mortar dust swept up and wheeled out. At 12:10am, after 27,000 steps, bruised and battered, it is done. Both beams are in place and ready to be secured, and I am off to eat and sleep. They are packed in with mortar, stone and tiles in episode 36, and the doorway at the top of the tower is opened up in episode 42.
Jobs like this are why a renovation takes as long as it does when you work alone. My timeline of year one puts this week in context, and my article on Sicilian stonework explains the walls I am cutting into.
Frequently asked questions
Can one person install a heavy oak lintel?
I did, but it was brutal. I used the work table and ladders to lift each beam in stages, and the second, around 100kg, had to come down, be trimmed and go up again.
Is a cheap SDS drill worth buying?
My €90 Dexter drills, with about a three year warranty, have done heavy work. One snapped, but against €400 for professional brands, replacing it made sense to me.
How do you cut an oak beam to an angle?
I screwed a guide made from scrap timber to the beam and followed it with a freshly sharpened chainsaw. Sharpening the chain locally cost €6.
Why do oak beams in a curved wall need angled ends?
The wall into my tower is curved, so two beams sit back to back and their ends have to be cut at an angle to seat into the pockets.
More episodes on the same job: Stone walls and lime



